Go to Top

chip carving patterns (6)

Chip Carving Patterns book by Wayne Barton

This is the primary tool you use when chip carving. The blade of this type of knife is usually shorter compared to other types with a large resin handle. With a shorter blade, your hand is closer to the material which helps you deliver a more accurate cut. The blade of the chip carving knife is also curved to an angle with a sharp and pointy nose which digs deep in material. You also need softening stones when working with those tools.

It is a very informative manual that starts by explaining about the history of chip carving and then gradually goes on to the more difficult tasks. It is very newbie-friendly with colored photographs to guide you along the way. When you have to cut through a pattern, cut position one on all your triangles then return to cut position two, and so on so forth. This will guarantee a more professional finish with cuts of the same positive stops throughout.

The grid pattern was penciled directly to the basswood practice board using 1/4″ squares. Each 3×2 grid motif was marked using a darker pencil line. If you’d like to add something or share your pattern with the community you are more then welcomed! We hope that these patterns will help you chip carving hobby.

This bevel difference between the material chipped away in contrast to the remaining surface creates a chip carve pattern. Its fine, straight grain, virtually homogenous creamy color, and, above all, softness and workability make it ideal for chip carving. Other workable woods include butternut, Spanish cedar, eastern white pine, catalpa, and paulownia.

Of course, when tracing you should use other tools like a. T-ruler, #2 pencil and even a compass to mark each and every line of the pattern. Wood like butternut are very easy to work with and also pleasurable. Avoid material like white oak for chip carving as they are very difficult to work with.

With the blade angle, you can use a coarser grit sanding stone while with the edges, always go with a sanding grit of at least 1,500. If you don’t feel confident with a particular cut, don’t do it.

chip carving tools

The third row shows the first large motif area and uses both free-from long line work as well as large triangle chip cuts. The central rectangle area can be used for a name, date, special event, or for a small free-from pattern. The second row uses the classic triangle chip cut with small oval free-form chips worked from the 3×2 motifs into the un-carved background space.

In fact, this is one of the main advantages of chip carving. Without further ado, here are some useful information about chip carving along with the tools you will need. By copying and scaling these band patterns you can make patterns of any size.

You will be able to make timeless works of art using inexpensive and basic tools quickly and easily. You can easily download chip grids online to use as tracing paper or a general guideline when chip carving.

  • We have further assisted you in making sure that each chip carving pattern from this collection is presented as a segment already prepared for copying.
  • The Chip Carver’s Workbook by Dennis Moor is a smaller 96 pages paperback book.
  • Mahogany is the last type of wood that is recommended for chip carving.
  • If you want to provide ragged walls altogether, then use a lower density would like butternut or brass wood.
  • If you already have a pattern printed on paper, then it is easy to transfer it to your wood using graphite paper.
  • Then start to lift your knife out towards where the other cut ended, while still adding pressure.

Chip Technology

Combining a simple rosette and the diamond patterns makes a new recognizable object – an Air Balloon. The carving may be left unpainted but if you decide to paint your chip carved balloon avoid too watery paint – it can bleed into the neighbor chips. The tree (fir) pattern combines 11 chips; one of them is four-corner (rectangular) chip for the trunk.

I tried many knives and I noticed that I tend to use a small chip carving knife that you may see on many pictures on the website. I think any chip carving knife can be used with success; finding a knife that fits your hand well is a plus. I usually carve on one side of a board that is 1/4“ (6 mm) thick; pick a thicker board especially if you plan to do chip carving on both sides. For cutting tasks, you want to go with a very high grit sanding stone in the range of grit size.

Chip Carving: Design & Pattern Sourcebook

Over 100 patterns to make drawer fronts, chair backs, and clockfaces, and mix and match these dozens of designs in hundreds of combinations. “The largest selection of patterns in any book. Sure to delight all who do chip carving.”– Chip Chats .

Basically, you simply push in the material in a perpendicular fashion with the stab knife to remove material. Since this requires a larger surface area, it also means that the stab knife blade needs to be sharp at all times. This is a collection of four Chip carving patterns. In the picture you can see that these are 4 simple band chip carving patterns that can serve not only beginners but also more experienced woodcarvers. The oldest European design is from a chest made in Switzerland and carved in 1449.

Additionally, do not cut too deep in your chip and the maximum should be around 1/8” deep. If your chip is too large, remove it in multiple stages rather than one pass.

Carved Wooden Plate 13″ Polish highlander Folk Art intricate chip carved pattern by Podhale Gorale

There are several methods that you can use to transfer a design to wood for chip carving successfully. Everyone have their particular way, and probably with time, you might even develop a favorite method. The Chip Carver’s Workbook by Dennis Moor is a smaller 96 pages paperback book. However, it is jammed-packed with information that will help you up your game as quickly as possible.

Elemental Tools Whittling Knife - Wood Carving Knife for Details

Leave a Reply